Before configuring the web interface, complete Step 2: How to Configure the Barracuda Load Balancer.
In this article:
Configure the Barracuda Load Balancer from the Web Interface
After specifying the IP address of the Barracuda Load Balancer and opening the necessary ports on your corporate firewall, configure the Barracuda Load Balancer from the web interface. Make sure the system being used to access the web interface is connected to the same network as the Barracuda Load Balancer, and that the appropriate routing is in place to allow connection to the Barracuda Load Balancer’s IP address via a web browser.
To configure administrative settings on the Barracuda Load Balancer:
- From a web browser, enter
http://followed by the IP address of the Barracuda Load Balancer, followed by the default web Interface HTTP Port (:8000).
- Log into the administration interface using admin for both the username and password.
- Go to the BASIC > IP Configuration page and perform the following steps:
- Enter the following information in the WAN IP Configuration section:
- IP Address. The address associated with the port that connects the Barracuda Load Balancer to the WAN.
- Subnet Mask. The subnet mask assigned to the WAN interface of the Barracuda Load Balancer.
- Default Gateway. The default router for network traffic not destined for the local subnet.
- Allow administration access. Set to Yes if you want to allow administration access using this IP address. The web interface port has a default of 8000 but can be changed on the BASIC > Administration page.
If the Barracuda Load Balancer is in Bridge-Path mode, or if only Direct Server Return mode is being employed, then go to Step 3c.
If you are configuring a passive Barracuda Load Balancer in a cluster, then go to Step 3c.
If the system becomes active and if it is in Route-Path mode, it will assume the LAN IP address and netmask that are configured on the originally-active Barracuda Load Balancer. See High Availability Deployment.
Enter the following information in the LAN IP Configuration section:
LAN IP Address and LAN Netmask. The address that connects the Barracuda Load Balancer to the LAN. This is only used for two-armed Route-Path mode or, if in one-armed Route-Path mode, for management.
Allow administration access. Set to Yes if you want to allow administration access using this IP address. The web interface port has a default of 8000 but can be changed on the BASIC > Administration page.
If desired, enter the following information in the Management IP Configuration section:
Management IP Address and Management Netmask. The management IP address can be used only for administration access and is optional. It should not be on the same network as either the LAN or WAN IP address. On certain 640 models, it is used by the MGMT port on the front of the unit; on most other models, it is used by the Ethernet port on the back of the appliance.
Allow administration access. Set to Yes. The web interface port has a default of 8000 but can be changed on the BASIC >Administration page.
- Enter the IP address of your primary and secondary DNS servers.
- Enter the default hostname and default domain name of the Barracuda Load Balancer.
- If the Barracuda Load Balancer is behind a proxy server, enter the relevant parameter.
Click Save Changes.
If you want this Barracuda Load Balancer to operate in Bridge-Path mode, and this is not a backup Barracuda Load Balancer in a cluster, click Convert to change the operation form Route-Path to Bridge-Path.
- Select BASIC > Administration, and perform the following steps:
Assign a new administration password to the Barracuda Load Balancer.
Make sure the local time zone is set correctly.
Time on the Barracuda Load Balancer is automatically updated via NTP (Network Time Protocol). It requires that port 123 is opened for outbound UDP traffic on your firewall (if the Barracuda Load Balancer is located behind one).
It is important that the time zone is set correctly because this information is used to coordinate traffic distribution and in all logs and reports. Also, if this system is going to be clustered with another one, both systems must have the same time zone.
If desired, change the port number used to access the Barracuda Load Balancer user interface. The default port is 8000.
Enter the amount of time, in minutes, for the length of your web interface session before you are logged off due to inactivity.
(Optional) Specify your local SMTP server. Enter the email address for your administrator to receive system alerts and notifications
- Click Save Changes.
the Barracuda Load Balancer has access to the activation servers, your Energize Update and Instant Replacement subscriptions are most likely active. If not, you will see a warning at the top of every page. You must activate your subscriptions before continuing.
Click on the link in the warning message or use the link on the BASIC > Status page to open up the Barracuda Networks Product Activation page in a new browser window. Fill in the required fields and click Activate. A confirmation page displays the terms of your subscription. On the BASIC > Status page, you may need to enter the activation code from the Barracuda Networks Product Activation page to activate your Barracuda Load Balancer.
Update the Barracuda Load Balancer Firmware
Use the following steps to update the firmware:
Go to the ADVANCED > Firmware Update page.
Read the release notes to learn about the latest features and fixes in the new firmware version.
Click Download Now next to Latest General Release. Click OK on the download duration window.
Updating the firmware may take several minutes. Do not turn off the unit during this process.
Download Now is disabled if the Barracuda Load Balancer is running the latest firmware version.
The Barracuda Load Balancer begins downloading the latest firmware version. Click Refresh to view the download status, until you see a message stating that the download has completed.
Click Apply Now when the download completes.
Click OK when prompted to reboot the Barracuda Load Balancer.
A Status page displays the progress of the reboot. Once complete, the login page appears.
Update the IPS Definitions
If you are configuring a passive Barracuda Load Balancer in a cluster, then you may skip this set of steps.
To apply the newest definitions for the Intrusion Prevention System:
- Select ADVANCED > Energize Updates.
- Select Hourly or Daily for Automatically Update. The recommended setting is Hourly for IPS definitions.
- Check to see if the current version is the same as the latest general release. If the rules are up-to-date, proceed to the next section. If the rules are not up-to-date, continue to the next step.
- Click Update to download and install the latest available IPS definitions onto the Barracuda Load Balancer.
- Click Save Changes.
Continue with Step 4: How to Configure Administrative Settings.