Default Port Configuration
Port Label | OS Notation | Speed/Type | Notes |
---|---|---|---|
1 | p1 | 10/100/1000 MBit RJ45 | |
2 | p2 | 10/100/1000 MBit RJ45 | |
3 | p3 | 10/100/1000 MBit RJ45 | |
4 | p4 | 10/100/1000 MBit RJ45 | DHCP |
5 | p5 | 10/100/1000 MBit RJ45 |
Hardware Specifications
Interface | |
---|---|
RJ45 Ethernet NICs | 5 x 1 Gbps (Intel I211) |
USB 3.0 | 2 |
Serial console | 1 [RJ45] |
Data Storage | |
RAM [GB] | 2 |
Mass Storage | |
Type | SSD |
Size [GB] | 80 |
Size, Weight, Dimensions | |
Appliance weight [kg] | 2.0 |
Carton weight with appliance [kg] | 3.9 |
Appliance size: width x depth x height [mm] | 232 x 153 x 44 |
Carton size: width x depth x height [mm] | 310 x 260 x 180 |
Form factor | Compact |
Hardware | |
Display | - |
Hardware crypto accelerator | Yes, built-in |
Cooling | Fanless |
Power supply | Single, external |
L-Shape rack mount bracket | Not included in packaging, available to order BPRAC-04 / BPIRAC-04 |
Environmental | |
Noise emission [db/A] | N/A |
Operating temperature [°C] | 0 to +40 |
Storage temperature [°C] | -20 to +70 |
Operating humidity (non-condensing) | 5% to 95% |
Certifications & Compliance | |
CE emissions | Yes |
CE electrical safety | Yes |
FCC emissions | Yes |
ROHS compliant | Yes |
Power & Efficiency | |
Power supply type | External |
Power type [AC/DC] | AC |
Input rating [Volts] | 100-240 |
Input frequency [Hz] | 50-60 |
Auto sense | Yes |
Wattage / max. power draw [W] | 45 |
Max. power draw (@ 230V) [A] | 0.2 |
Max. heat dissipation [W] | 19 |
Max. heat dissipation [BTU] | 65 |
Energy efficiency [average] | > 85% |
LEDs and Acoustic Signals
Your appliance is equipped with a variety of LEDs and acoustic signals. The front panel of the Barracuda SecureEdge T100 contains one power LED (blue), one disc LED (green), one status LED (green/red), and 5 port LEDs. On the back panel, you can see one power button LED and various port LEDs. Two acoustic signals indicate status of installation. The tables below show the different meanings of the different glowing states and acoustic signals:
LED Color | Status | Meaning Installation | Meaning Operation |
---|---|---|---|
All LEDs Off | Off | Appliance is powered off or installation has not initialized far enough for LED control when installation is started. | Appliance is powered off. |
Power LED front side - BLUE | Steady | - | Appliance is plugged in and is on. |
Status LED front side - GREEN/RED | Off | Installation has not initialized far enough for LED control when installation is started. | - |
Status LED front side - GREEN | Steady | After a hotfix installation, the LED turns to green until the next reboot in case the hotfix installation was successful. This feature requires firmware 7.1.3 or higher OR 7.2.2 or higher. | Box is running normally, or installation has finished successfully. |
Status LED front side - GREEN | Blinking slowly (1/s interval) | Normal installation. | Appliance is either booting, shutting down, or performing a system update. |
Status LED front side - RED | Steady | After a hotfix installation, the LED turns to red until the next reboot in case the hotfix installation failed. This feature requires firmware 7.1.3 or higher OR 7.2.2 or higher. | Appliance is halted and may be disconnected, or an error occurred preventing the appliance from entering the up state. |
Disc LED - GREEN | Blinking | Appliance is reading or writing on storage. | Appliance is accessing the internal storage. |
Port LEDs - GREEN/YELLOW | Left blinking | Data transfer – Yellow (10/100 Mbps) | Port in use. |
Right steady | - | Port is on. | |
PSU LEDs - GREEN | Steady | PSU modules connected and running | Power supply unit is up and running. |
Off | Power defective, standby, or shutdown | Power supply unit is off or in standby mode. |
Acoustic Signal | Frequency | Meaning |
---|---|---|
Beep | 1 time (.) | Appliance is booting. |
Beep | 3 times (...) | Installation was completed successfully; appliance is halted for reboot. After reboot, one beep will again indicate booting. |
Beep | 3 times long (_ _ _) | Error during installation. |
Serial Console Port
In order to establish a console connection to the appliance using an RJ45 serial cable, you need to configure the serial port on the terminal using the following parameters:
Parameter | Value |
---|---|
Baud | 19200 |
Bits | 8 |
Stop bit | 1 |
Parity | None |
Handshake | None |