Default Port Configuration
Port Label | OS Notation | Speed/Type | Management Port |
---|---|---|---|
1 | p1 | 10/100/1000 MBit RJ45 | X |
2 | p2 | 10/100/1000 MBit RJ45 | |
3 | p3 | 10/100/1000 MBit RJ45 | |
4 | p4 | 10/100/1000 MBit RJ45 | |
5 | p5 | 10/100/1000 MBit RJ45 |
Hardware Specifications
Interface | |
---|---|
RJ45 Ethernet NICs | 5x10/100/1000 |
USB 3.0 | 2 |
Serial console | 1 [RJ45] |
VGA | No |
Integrated Wi-Fi (IEEE 802.11b/g/n) | Yes |
System | |
CPU | Intel Apollo Lake |
RAM [GB] | 4 |
Mass Storage | |
Type | SSD |
Size [GB] | 80 or higher |
Size, Weight, Dimensions | |
Appliance weight [kg/lbs] | 2.0 / 4.4 |
Carton weight with appliance [kg/lbs] | 3.5 / 7.7 |
Appliance size: width x depth x height [in/cm] |
|
Carton size: width x depth x height [in/cm] |
|
Hardware | |
Form Factor | Desktop |
Display | - |
Cooling | Fanless |
Power supply | Single, external |
L-shape rack mount brackets | Not included in packaging. Must be ordered separately. |
Wall-mount brackets | No |
Din-rail mount clip | - |
USB | 2x USB 3.0 |
Environmental | |
Noise emission [db/A] | N/A |
Operating temperature [°C] | 0 to +40 |
Storage temperature [°C] | -20 to +70 |
Operating humidity (non-condensing) | 5% to 95% |
Certifications & Compliance | |
CE emissions | Yes |
CE electrical safety | Yes |
FCC emissions | Yes |
ROHS compliant | Yes |
Power & Efficiency | |
Power supply | Single, external |
Power supply input voltage | 100 – 240 V, AC |
Power supply output voltage | 12 V, DC |
Power supply voltage | 50 Hz – 60 Hz |
Power supply watts | 45 W |
MTBF [yrs.] | > 5 |
Max. heat dissipation [W] | 26.7 |
Max. heat dissipation [BTU] | 90.9 |
Energy efficiency [average] | > 93% |
Packaging Content | |
Appliance | Yes |
Serial cable | No |
Straight network cable | Yes |
External power brick and cable | Yes |
USB flash drive for recovery & installation | Yes |
Wireless Antenna | Yes |
Quick Start Guide | Yes |
LEDs and Acoustic Signals
Your appliance is equipped with a variety of LEDs and acoustic signals. Barracuda CloudGen Firewall F80 B has on the front side one power LED (blue), one disc LED (green), one status LED (green/red) and 5 port LEDs and on the back side one power button LED and various port LEDs. Two acoustic signals indicate status of installation. The tables below show the different meanings of the different glowing states and acoustic signals:
LED Color | Status | Meaning Installation | Meaning Operation |
---|---|---|---|
All LEDs Off | Off | Appliance is powered off or installation has not initialized far enough for LED control when installation is started. | Appliance is powered off. |
Power LED front side - BLUE | Steady | - | Appliance is plugged in and is on. |
Status LED front side - GREEN/RED | Off | Installation has not initialized far enough for LED control when installation is started. | - |
Status LED front side - GREEN | Steady | After a hotfix installation, the LED turns to green until the next reboot in case the hotfix installation was successful. This feature requires firmware 7.1.3 or higher OR 7.2.2 or higher. | Box is running normally, or installation has finished successfully. |
Status LED front side - GREEN | Blinking slowly (1/s interval) | Normal installation. | Appliance is either booting, shutting down, or performing a system update. |
Status LED front side - RED | Steady | After a hotfix installation, the LED turns to red until the next reboot in case the hotfix installation failed. This feature requires firmware 7.1.3 or higher OR 7.2.2 or higher. | Appliance is halted and may be disconnected, or an error occurred preventing the appliance from entering the up state. |
Disc LED - GREEN | Blinking | Appliance is reading or writing on storage. | Appliance is accessing the internal storage. |
Port LEDs - GREEN/YELLOW | Left blinking | Data transfer – Yellow (10/100 Mbps) | Port in use. |
Right steady | - | Port is on. | |
PSU LEDs - GREEN | Steady | PSU modules connected and running | Power supply unit is up and running. |
Off | Power defective, standby, or shutdown | Power supply unit is off or in standby mode. |
Acoustic Signal | Frequency | Meaning |
---|---|---|
Beep | 1 time (.) | Appliance starts booting. |
Beep | 3 times (...) | Installation was completed successfully; appliance is halted for reboot. After reboot, one beep will again indicate booting. |
Beep | 3 times long (_ _ _) | Error during installation. |
Serial Console Port
In order to establish a console connection to the appliance using an RJ45 serial cable, you need to configure the serial port on the terminal using the following parameters:
Parameter | Value |
---|---|
Baud | 19200 |
Bits | 8 |
Stop bit | 1 |
Parity | None |
Handshake | None |