It seems like your browser didn't download the required fonts. Please revise your security settings and try again.
Barracuda CloudGen Firewall

F380 Revision B

  • Last updated on

F380B_FrontRack.png

F380B_Back.png

Default Port Configuration

Port LabelOS NotationSpeed/TypeManagement Port
1p110/100/1000 MBit RJ45X
2p210/100/1000 MBit RJ45 
3p310/100/1000 MBit RJ45 
4p410/100/1000 MBit RJ45 
5p510/100/1000 MBit RJ45 
6p610/100/1000 MBit RJ45 
7p710/100/1000 MBit RJ45 
8p810/100/1000 MBit RJ45 
9a110 GbE Optical Fiber SFP+ 
10a210 GbE Optical Fiber SFP+ 

The CloudGen Firewall hardware appliances ship with a Quick Start Guide. Follow this guide to connect to your firewall. To protect your network, follow the instructions for the standard deployment.

Hardware Specifications

Warranty and Safety Instructions

Opening your Barracuda Networks appliance or removing its warranty label unless instructed to do so by Barracuda Networks support will void your warranty and hardware support. Barracuda Networks Appliance Safety Instructions

Interface

RJ45 Ethernet NICs

8 x 1 GbE

SFP+ 10G Fiber NICs

2 x 10 GbE

USB 3.02
Serial console1 [RJ45]
System
CPUIntel Celeron G-Series, 2 cores
RAM [GB]4
Mass Storage
TypeSSD
Size [GB]120 GB or higher
Size, Weight, Dimensions
Appliance weight [kg]8.4
Carton weight with appliance [kg]9.4
Appliance size: width x depth x height [mm]440 x 440 x 44
Carton size: width x depth x height [mm]

755 x 555 x 203

Form factor1U Rack Mount

Hardware

DisplayYes
CoolingFan
Power supplySingle, internal
Environmental
Noise emission [db/A]N/A
Operating temperature [°C]0 to +40
Storage temperature [°C]-20 to +70
Operating humidity (non-condensing)10% to 85%
Certifications & Compliance
CE emissionsYes
CE electrical safetyYes
FCC emissionsYes
ROHS compliantYes
Power & Efficiency
Power supplySingle
Power supply typeInternal
Power type [AC/DC]AC
Input rating [Volts]100-240
Input frequency [Hz]50-60
Auto senseYes
Wattage / max. power draw [W]174
Max. power draw (@ 120V) [A]12
Max. power draw (@ 230V) [A]6
Max. heat dissipation [W]23
Max. heat dissipation [BTU]77
Energy efficiency [average]> 87%

The hardware specifications list was valid at the time this manual was published. The listed components are subject to change at any time, as Barracuda Networks may change hardware components due to technological advancements. Therefore, the list may not reflect the current hardware configuration of the Barracuda Networks appliance it was delivered with.

LEDs and Acoustic Signals

Your appliance is equipped with a variety of LEDs and acoustic signals. On the front of the Barracuda CloudGen Firewall F380 B are 4 LEDs indicating connected network port link connections, one power LED, and one disc LED. On the back side of the unit is a power button with included LED. The tables below show the different meanings of the different glowing states and acoustic signals:

LED ColorStatusMeaning InstallationMeaning Operation

All LEDs Off

Off

Appliance is powered off or installation has not initialized far enough for LED control when installation is started.

Appliance is powered off.

Power LED front side - GREEN

Steady

Please follow instructions on the LCD Display.

Appliance is plugged in and is on.

Disc LED front side - YELLOW

Blinking

Appliance is reading or writing on storage.

Appliance is accessing the internal storage.

Port LEDs - GREEN/YELLOW

Left blinking

Data transfer – Yellow (10/100 Mbps)

Port in use.
 Right steady-Port is on.

PSU LEDs - GREEN

Steady

PSU modules connected and running

Power supply unit is up and running.
OffPower defective, standby, or shutdownPower supply unit is off or in standby mode.
Acoustic SignalFrequencyMeaning Installation
Beep1 time

Unit starts booting

Beep3 timesInstallation is completed successfully and appliance is halted for reboot. After reboot, one beep indicates booting.

Serial Console Port

In order to establish a console connection to the appliance using a serial cable (RJ45), you need to configure the serial port on the terminal using the following parameters:

ParameterValue
Baud19200
Bits8
Stop bit1
ParityNone
HandshakeNone

LC Display

Navigating

This security appliance features a key pad with four keys and an LCD panel on the left side of the front panel. These may be used to obtain certain information and to perform certain commands directly on the appliance.

Keyboard Button
Command
Left arrow or Escape key

Navigates back or acts like an Escape key while working in the LCD menu.

Up arrow

Navigates up or increases a value.

Down arrow

Navigates down or decreases a value.

Right or Enter

Navigates forwards or acts like an Enter key for confirming a configuration step.

LCD Display Menu

You may use the LCD display and the keypad to access certain appliance features. Use the up and down keys to navigate through the items of the main menu.

The LCD menu features the following items from top to bottom:

LCD Menu
Meaning
Appliance type, OS version and release numberThis is the default display.
IP address and subnet maskShows the configured IP address and subnet mask of the appliance.
Time and dateShows time and date currently configured on the appliance.
Uptime of Barracuda OSThe uptime in days, hours and minutes.
Serial number of the applianceUnique identifier for the appliance.
Shutdown menuEnables you to shut down the appliance.
Reboot menuEnables you to reboot the appliance.
Menu to change the management IP addressConfigure the IP address for the management port.
Menu to boot into ART during the next reboot

Enables you to set a flag that will cause the appliance to boot into ART the next time it is rebooted.
Once set, this flag can not be deleted through the menu. When rebooted, the appliance will not start Barracuda OS, but ART instead. You may connect to the appliance by using the serial console or by SSH. A Control Center managed box running in ART mode cannot be managed through the CC, although it will build a connection to the CC signaling its presence.