Activate and Update Barracuda Products

Depending on whether your Barracuda Networks product has Internet access, you can complete either an online or offline activation and update.

This article applies to the following Barracuda Networks products:

• Barracuda Link Balancer
• Barracuda Load Balancer ADC
• Barracuda Email Security Gateway
• Barracuda SSL VPN
• Barracuda Web Application Firewall
• Barracuda Web Security Gateway
• Barracuda Backup
• Barracuda Message Archiver

For products not listed here, see the specific product space for activation setup.

Firewall Ports

Click on the product to view and verify the list of required firewall ports to open.

• Barracuda Load Balance ADC
• Barracuda Email Security Gateway
• Barracuda SSL VPN
• Barracuda Web Application Firewall
• Barracuda Web Security Gateway
• Barracuda Backup
• Barracuda Message Archiver

Online Activation and Update

Complete the following steps to initiate the online activation process and update the system:

1. In a web browser, enter the IP address and default HTTP port of the device. For example, enter: http://192.168.200.200:8000/

2. Log in using admin for the username. For the password:
   If your appliance serial number is higher than 1311431, then the default administrator password is the numeric portion of the serial number. If your serial number is 1311431 or lower, then the default administrator password is admin. For help finding the serial number of your appliance, see Serial Number for Hardware and Virtual Appliances.

3. Go to the BASIC > Dashboard page, and view the Subscription Status section to verify that your Energize Updates subscription status displays as Current. If the device can access the activation servers, your Energize Updates and Instant Replacement subscriptions are most likely active. If not, a warning displays at the top of every page. You must activate your subscriptions before continuing. If the Energize Updates subscription status displays as Not Activated, complete the following:

   1. Click the activation link at the top of the page and complete your subscription activation. 
   2. Go to the Subscription Status section of the BASIC > Dashboard page, and click Refresh to automatically update the Energize Updates subscription activation status.
4. Go to the ADVANCED > Firmware Update page and verify that the currently installed version is the latest general release. If you have the latest firmware version already installed, the Download Now button is disabled.
5. If there is a new Latest General Release available:
   1. Click Download Now and allow the update to finish downloading.

   2. After the update is completely downloaded, click Apply Now.

      Do not reboot or turn off the device while the firmware is updating. After the process completes, the device automatically reboots and you are redirected to the login page.

6. Log in again, go to the BASIC > Administration page, and change the administrator password in the Password Change section.

Offline Activation and Update

Step 1. Obtain Feature and Activation Codes

1. Contact Barracuda Networks Technical Support to obtain a Feature Code to enable offline updates.
2. Go to the Barracuda Networks product Activation page, complete the form, and obtain an Activation Code.

Step 2. Activate and Update Device

If your device does not have Internet access, use the following steps to manually enter your Activation Code to activate the device, and then enable offline updates to apply the update packages downloaded in Step 2. Download Updates.

1. In a web browser, enter the IP address and default HTTP port of the device. For example, enter: http://192.168.200.200:8000/
2. Log in using admin for the username. For the password:
   If your appliance serial number is higher than 1311431, then the default administrator password is the numeric portion of the serial number. If your serial number is 1311431 or lower, then the default administrator password is admin. For help finding the serial number of your appliance, see Serial Number for Hardware and Virtual Appliances.

3. Activate your device:

   1. Go to the BASIC > Dashboard page.

   2. In the Subscription Status section, enter the Activation Code, and then click Activate.

4. Enable offline updates:
   1. Append the URL with &expert=1 to enable expert mode; the ADVANCED > Offline Update page displays.
   2. Enter the Feature Code, and then click Activate. 
   3. When the Enable Offline Updates setting appears, select Yes.
   4. Click Save Changes.
5. Update your firmware:
   1. Go to the ADVANCED > Firmware Update page.
   2. In the Firmware Upload section, click Browse to navigate to and select the firmware package that you downloaded from your Barracuda Cloud Control account.

   3. Click Upload. After the firmware package is completely uploaded, click Apply Now.

       Do not reboot or turn off the device while the firmware is updating. After the process completes, the device automatically reboots and you are redirected to the login page.

6. Update definitions:
   1. Go to the ADVANCED > Energize Updates page.
   2. In the Definition Update Upload section, click Browse to navigate to and select a definition package that you downloaded from your Barracuda Cloud Control account.
   3. After the definition package is completely uploaded, click Apply Now.
   4. Repeat steps 6b and 6c until you have updated all of the definitions on the page.

7. Go to the BASIC > Administration page, and change the administrator password in the Password Change section.