When you add network modules to Barracuda appliances or virtual network adapters to virtual systems, you must add these network interfaces to the network configuration of your Barracuda NG Firewall. Every Barracuda NG Firewall model has its own set of interface names (naming eth
In this article:
Before you Begin
Find out which network driver is needed for your network adapter/interface.
Step 1. Add Network Interface(s)
Add the additional network interfaces to the Barracuda NG Firewall.
- Open the Network page (Config > Full Config > Box).
- In the left pane, click Interfaces.
- Expand the Configuration Mode menu, and then click Switch to Advanced.
- Click Lock.
- In the Network Interface Cards table, add or edit an entry for the NIC. For more information on the NIC settings, see the following section.
- To dynamically update the settings in the Physical Interfaces table, select yes from the Interface Computation list. The physical interface settings are updated whenever the network configuration is changed. Otherwise, you must manually update settings.
- In the Physical Interfaces table, add or edit an entry for your physical interface. For more information on the physical interface settings, see the following section.
- In the Internal Interface Configuration table, add loopback equivalent devices.
- Click Send Changes and Activate.
Step 2. Activate Network Changes
You must activate the network changes to add the network devices.
- Open the Box page (Control > Box).
- In the left menu, expand the Network section and click Activate new network configuration.
- Select Failsafe. The 'Failsafe Activation Succeeded' message is displayed after your new network configurations have been successfully activated.
The Barracuda NG Firewall can now send traffic over the new network interfaces.
Interface Parameters Description
Network Interface Cards Table
Descriptions of the settings that you can configure in the Network Interface Cards table:
Driver Module Name
The driver that is used for the NIC. Only recommended cards are listed. If you require a card that is not listed, see the list of supported NICs to verify that your card is supported. To manually enter the card name, select the Other check box and enter the card name in the Driver Module Name field.
Number of Interfaces
The number of NIC interfaces that can be used simultaneously. This indicates the number of ports and not the number of cards of the particular type. For example, one dual-port NIC counts as two interfaces, but one combo-type card with support for three different connectors (for example, BNC, AUI, RJ45) counts as one because only one connection is active at one time. If you enter
This setting is used with module-based driver support. For more information, see. Note that several interface-specific option strings may be added to this table. They are formatted as:
with N being the number of interfaces.
(Advanced Configuration Mode) Activates an alternative NIC driver that is defined via the Fallback Module Name and Fallback Driver Options settings. This setting might be helpful during and after updating sequences. If the primary driver does not work, the fallback driver is used. If the fallback driver does not work, both drivers are loaded.
Fallback Module Name/Fallback Driver Options
(Advanced Configuration Mode) The fallback driver to be used for the NIC. Only recommended cards are listed. If you require a card that is not listed, see the list of supported NICs to verify that your card is supported.
|Enable or disable the driver.|
|NIC Type||NIC type. This information is used for logical consistency checks. In conjunction with the specified number of interfaces, it is possible to check whether a particular interface may be referenced in some of the other sections. Available NICs: Ethernet.|
(Advanced Configuration Mode)
(Advanced Configuration Mode) Specifies if driver support is module-based or kernel-based. Default is Loadable_Module.
The MTU size for an Ethernet NIC. Packets exceeding this value are fragmented when sent. This MTU is used as the default value for all existing interfaces. To specify an MTU for an interface, edit its MTU setting in the Physical Interfaces table.
MTUs can also be set for virtual LANs, box network, additional networks, and standard routing. The maximum accepted MTU of the next hop is used.
Physical Interfaces Table
The MTU for the interface. This setting overrides the MTU that is entered in the Network Interface Cards table.
If nothing else has been configured, all recognized interfaces are generally available by default. Interfaces can be claimed for exclusive use by xDSL (Connection Type: PPPOE) and DHCP links (see How to Configure an ISP with Dynamic IP Addresses (DHCP)). When an interface has been claimed as Modem Interface or DHCP Interface, its usage is set to status Reserved. If an interface is claimed by multiple services concurrently, its usage status is set to Overbooked.
An interface that has not been claimed by a service is flagged with none. Interfaces claimed by xDSL or DHCP links are flagged with xdsl or dhcp, respectively, followed by the link name as specified in the xDSL/DHCP configuration area when creating the link. For example, xdsl::xDSLLinkName.
|Name of NIC|
The NIC name as specified in the Network Interface Cards table.
The NIC type as specified in the Network Interface Cards table.
The driver module driver name as defined in the Network Interface Cards table.
If the driver module does not support static network speed and duplex mode settings, select no in order to manually enter these settings. Speed and duplex mode options that cannot be steered through the NIC driver are manually set to a static value via the ethtool utility.
|Forced Speed [Mpbs]|
The static network speed for the NIC. To manually set the forced speed, enable autonegotation and select 10, 100, or 1000 Mbps.
The static duplex mode for the NIC. To manually set the duplex mode, enable autonegotation and select half or full.