We use cookies on our website to ensure we provide you with the best experience on our website. By using our website, you agree to the use of cookies for analytics and personalized content.This website uses cookies. More Information
It seems like your browser didn't download the required fonts. Please revise your security settings and try again.
Barracuda CloudGen Firewall

This Firmware Version Is End-Of-Support

Documentation for this product is no longer updated. Please see https://campus.barracuda.com/doc/71862301/ for further information on our EoS policy.

Barracuda NG Firewall F200 / F201 Revision B

  • Last updated on

Opening your Barracuda Networks appliance or removing its warranty label unless instructed to do so by Barracuda Networks support will void your warranty and hardware support.

Barracuda Networks Appliance Safety Instructions

Always use the power supply shipped with the appliance.


 Revision B
Minimum Firmware Requirement5.2.x and later

Default Port Configuration

LabelOS NotationSpeed/TypeManagement Port
1port110/100/1000 MBit RJ45X
2port210/100/1000 MBit RJ45 
3port310/100/1000 MBit RJ45 
4port410/100/1000 MBit RJ45 

Hardware Specifications

Memory2 GB
HDD (formatted)40 to 320 GB SSD or HDD (Depending on model revision)
SSD (formatted)-
Flash Disk128 MB
USB2x USB 2.0
Form FactorDesktop
Dimensions (W/D/H)37.5 x 19 x 5 cm
14.8 x 7.5 x 2.0 in  

When planning to deploy this model with the Barracuda 19" Rackmount Shelf Kit, please take into consideration, that the overall height exceeds one rack unit (1 RU).

Net Weight3,8 kg
Power Supply Input Voltage100 - 240 V, AC
Power Supply Output Voltage12 V, DC
Power Supply Voltage47 Hz - 63 Hz
Power Supply Watts60 W
Storage Temperature-20 °C - +70 °C
Operation Temperature0 °C - 40 °C
Relative Humidity5% - 95%, non-condensing
Fan1 System Fan
CertificationsCE, FCC, ROHS
WiFi (F201 only)802.11 b/g/n up to 150 Mbps single antenna extended range

The hardware specifications list was valid at the time this manual was published. The listed components are subject to change at any time, as Barracuda Networks may change hardware components due to technological progress. Therefore, the list may not reflect the current hardware configuration of the Barracuda Networks NG Firewall or NG Control Center appliance it was delivered with.

Status LED

Your appliance is equipped with a variety of LEDs. One of them is the Status LED. It is either labeled with a heart symbol or the term Status. It indicates the appliance’s operational state by changing colors between green, orange and red and by changing between blinking and steady glowing. The table below shows the different meanings of the different glowing states.

ColorGlowing StateMeaning installationMeaning Normal Operation or Active Recovery Technology Operation

Appliance is powered off or installation has not initialized far enough for LED control when installation is started.

Appliance is powered off.
GreenBlinkingNormal installation.

Appliance is either booting, shutting down or performing a system update.


Installation was completed successfully, appliance is halted for reboot or installation was not yet initialized far enough for LED control.

Barracuda NG Firewall is up and running.
RedBlinkingError during installation.

An error has appeared preventing Barracuda NG Firewall from entering the up state.
If no orange light available: appliance is in ART mode.

RedSteady-Appliance is halted and may be disconnected.
OrangeSteady-Appliance is in ART mode.

Not all appliances support orange and/or red LED colors. Depending on the appliance type, the status LED might be on by default and it might take some time during boot and installation to start either blinking or changing the color. Furthermore, the status LED might blink at different frequencies.

Serial Console Port

In order to establish a console connection to the appliance using a serial cable (Revision A: DB9, Revision B: RJ45), you need to configure the serial port on the terminal using the following parameters:

Stop bit1



Last updated on