We use cookies on our website to ensure we provide you with the best experience on our website. By using our website, you agree to the use of cookies for analytics and personalized content.This website uses cookies. More Information
It seems like your browser didn't download the required fonts. Please revise your security settings and try again.
Barracuda CloudGen Firewall

This Firmware Version Is End-Of-Support

Documentation for this product is no longer updated. Please see https://campus.barracuda.com/doc/71862301/ for further information on our EoS policy.

Barracuda NG Firewall F400 Revision A

  • Last updated on

Opening your Barracuda Networks appliance or removing its warranty label unless instructed to do so by Barracuda Networks support will void your warranty and hardware support. Barracuda Networks Appliance Safety Instructions

The standard model of Barracuda's NG Firewall F400 comes with eight 10/100/1000 MBit RJ45 Ethernet ports and a single power supply. Other F400 model types provide different port combinations and a dual power supply.

Standard Model Port Configuration

LabelOS NotationSpeed/TypeManagement Port
1port110/100 MBit RJ45X
2port210/100/1000 MBit RJ45 
3port310/100/1000 MBit RJ45 
4port410/100/1000 MBit RJ45 
5port510/100/1000 MBit RJ45 
6port610/100/1000 MBit RJ45 
7port710/100/1000 MBit RJ45 
8port810/100/1000 MBit RJ45 

Model F20 Port Configuration

LabelOS NotationSpeed/TypeManagement Port
1port110/100 MBit RJ45X
2port210/100/1000 MBit RJ45 
3port310/100/1000 MBit RJ45 
4port410/100/1000 MBit RJ45 
5port510/100/1000 MBit RJ45 
6port610/100/1000 MBit RJ45 
7port710/100/1000 MBit RJ45 
8port810/100/1000 MBit RJ45 
9port191 GbE Fibre SFP 
10port101 GbE Fibre SFP 
11port111 GbE Fibre SFP 
12port121 GbE Fibre SFP 

Hardware Specifications

ComponentSpecifications
CPUIntel Dual Core
Memory2 GB
Mass Storage1 x 500 GB HDD
Flash Disk128 MB
LCD Module2 x 20 characters
USB2x USB 2.0
Form Factor1U rack mount
Dimensions (W/D/H)42,6 x 39,6 x 4,4 cm
16.8 x 16.6 x 1.7 in
Net Weight5.4 kg / 12 lbs
Power SupplySingle, internal
Power Supply Input Voltage100 - 240 V, AC
Power Supply Voltage47 Hz - 63 Hz
Power Supply Watts220 W
Storage Temperature-20 °C - +70 °C
Operation Temperature0 °C - 40 °C
Relative Humidity5% - 95%, non-condensing
CertificationsCE, FCC, ROHS
Wi-Fi (F301 only)802.11 b/g or better extended range Wi-Fi adapter

The hardware configuration list in Table 1 was valid at the time this manual was published. The listed components are subject to change at any time, as Barracuda Networks may change hardware components due to technological advancements. Therefore, the list may not reflect the current hardware configuration of the Barracuda Networks NG Firewall or NG Control Center appliance it was delivered with.

Status LED

Your appliance is equipped with a variety of LEDs. One of them is the Status LED. It is labeled either with a heart symbol or the term Status. It indicates the appliance’s operational state by changing colors between green, orange, and red and by changing between blinking and steady glowing. The table below shows the different meanings of the different glowing states.

ColorGlowing StateMeaning installationMeaning Normal Operation or Active Recovery Technology Operation
OffOff

Appliance is powered off or installation has not initialized far enough for LED control when installation is started.

Appliance is powered off.
GreenBlinkingNormal installation.

Appliance is either booting, shutting down or performing a system update.

GreenSteady

Installation was completed successfully, appliance is halted for reboot or installation was not yet initialized far enough for LED control.

Barracuda NG Firewall is up and running.
RedBlinkingError during installation.

An error has appeared preventing Barracuda NG Firewall from entering the up state.
If no orange light available: appliance is in ART mode.

RedSteady-Appliance is halted and may be disconnected.
OrangeBlinking--
OrangeSteady-Appliance is in ART mode.

Not all appliances support orange and/or red LED colors. Depending on the appliance type, the status LED might be on by default and it might take some time during boot and installation to start either blinking or changing the color. Furthermore, the status LED might blink at different frequencies.

Serial Console Port

In order to establish a console connection to the appliance using a serial cable (RJ45), you need to configure the serial port on the terminal using the following parameters:

ParameterValue
Baud19200
Bits8
Stop bit1
ParityNone
HandshakeNone

LC Display

Navigating

This security appliance features a key pad with four keys and an LCD panel on the left side of the front panel. These may be used to obtain certain information and to perform certain commands directly on the appliance.

KeyCommand
Left or Escape

Navigates back or acts like an Escape key while working in the LCD menu.

Up

Navigates up or increases a value.

Down

Navigates down or decreases a value.

Right or Enter

Navigates forth or acts like an Enter key for confirming a configuration step.

LCD Display Menu

You may use the LCD display and the keypad to access certain appliance features. Use the up and down keys to navigate through the items of the main menu.

The LCD menu features the following items from top to bottom:

MenuMeaning
Appliance type, OS version and release numberThis is the default display.
IP address and subnet maskShows the configured IP address and subnet mask of the appliance.
Time and dateShows time and date currently configured on the appliance.
Uptime of Barracuda OSThe uptime in days, hours and minutes.
Serial number of the applianceUnique identifier for the appliance.
Shutdown menuEnables you to shut down the appliance.
Reboot menuEnables you to reboot the appliance.
Menu to change the management IP addressConfigure the IP address for the management port.
Menu to boot into ART during the next reboot

Enables you to set a flag that will cause the appliance to boot into ART the next time it is rebooted.
Once set, this flag can not be deleted through the menu. When rebooted, the appliance will not start Barracuda OS, but ART instead. You may connect to the appliance by using the serial console or by SSH. A Control Center managed box running in ART mode cannot be managed through the CC, although it will build a connection to the CC signaling its presence.

Last updated on