On the Box page, you can configure and control key aspects of the Barracuda NextGen Firewall F-Series box operation. To access the Box page, open the CONTROL tab and click the Box icon in the ribbon bar.
When expanded in the left pane, the Time menu shows the system time and provides you with the following options to view and configure the time settings for the F-Series Firewall:
- Get Time – Displays the current time and date on the firewall.
- Show Settings – Displays the current NTP settings in the Report window..
- Set Time – Changes the current time and date to the values selected from the time and date fields. If your firewall is synchronized with an external time server, this manual change is overwritten by the succeeding time synchronization.
- Restart NTP – Restarts all NTP services.
- Synchronize Time – Offers an option dialog to synchronize the time settings with an NTP server.
When you expand the Network menu, you are provided with the following options to verify, restart, and activate the network configuration of the F-Series Firewall:
Verify active network configuration
This option checks the currently active network configuration for errors. The result appears in the Report window.
Restart active network configuration
This option shuts down and then restarts the currently active network configuration.
Verify new network configuration
This option checks new network configurations for errors after they have been successfully sent. The result appears in the Report window.
Activate new network configuration
This option activates new network configurations after they have been successfully verified. You can activate the new network configuration in the following modes:
- Activate now – The Activate now option is offered when a management IP address has been changed. With this mode, the firewall activates the network change and reconnects to the new IP address.
Failsafe – Failsafe network activation is the safest way to activate configuration changes. Always use this activation method on productive firewalls, e.g., to do the following:
- Add and delete network interfaces.
- Change network interface configurations.
- Add and delete policy routes.
- Delete direct and gateway routes.
With this mode, the firewall creates a backup file of the active network configuration. It then temporarily activates the configuration changes and verifies that the firewall can still be contacted via Barracuda NextGen Admin. If this verification is successful, the network is restarted so that the changes are activated permanently. If verification fails within the timeout defined in the Set Timeout field, the original network configuration is restored.
- Force – Forced network activation immediately activates the new network configuration with a logical consistency check ,but without creating a backup file of the active network configuration.
- Soft – Soft network activation can only be used after you add
Do not use 'Soft' network activation for the following:
or to an existing configuration.
- Adding or deleting source-based routes.
- Permanently deleting direct or gateway routes. Direct and gateway routes that have been deleted with 'Soft' network activation are marked as wild on the Network Page page. To delete these types of routes, use 'Failsafe' network activation instead, or restart the network. To restart the firewall, expand the menu.
If dynamic network connections have been configured, you can control them with options (off, on, start, stop, restart, reset) from the Dynamic Networks menu. You can control the following types of network connections:
- DHCP (cable)-connections
- Wireless WAN (WWAN)
- MGMT (box management)
- Tunnel connections
From the Operating System menu, you can control the F-Series Firewall. The menu provides you with the following options:
- Reboot Box – Reboots the firewall. If the firewall is not easily accessible, use caution when using this option because some firewalls might have problems with BIOS settings and fail to reboot or get stuck on a lower layer.
Firmware Restart – Shuts down and then restarts all servers and services belonging to the firewall subsystem, including the firewall engine.
Using this option is similar to running the
/opt/phion/bin/phionctrl startupcommands, except the control daemon itself is not stopped and started.
- Shutdown Box – Turns off the firewall.
- Save current Config for ART – Saves the current configuration of the firewall to the ART crash recovery OS. If the firewall must be reinstalled remotely, it uses the current system configuration for the recovery process.
- Install Update – Installs the selected firmware updates, hotfixes, or patches. The update process can be triggered after the package is successfully uploaded to the unit.
- Generate System Report – Creates a system report.
- Reset SMS Counter – Resets the counter for the number of successive SMS commands that have been accepted by the interface.
From the Domain Control menu, you can register the F-Series Firewall as a Windows domain member or view its domain registration status. The menu provides you with the following options:
- Show Registration Status – Displays the registration status of the firewall at a Windows domain.
- Register at Domain – Registers the firewall as a Windows domain member at a domain controller. In the User Authentication window, enter the username and password for the user with the appropriate administrative rights to add the firewall to the domain. Before you can use this option, configure an Authentication service.
- Register Proxy at Domain – Registers the HTTP Proxy at the Windows domain.
You can specify the level of authentication that is required for non-interactive Barracuda NextGen Control Center logins and HA synchronization.
After you expand the Authentication Level menu, you can select one of the following options:
No Authentication – Level -1; no authentication is required to send or retrieve configuration data.
- Check Key or IP address – Level 0; an IP address or key challenge is required. This option is still quite unsecure.
- Check IP address – Level 1, still quite unsecure.
- Check Key – Level 2, still quite unsecure.
- Check Key and IP address – Level 3, default setting. Do not change it unless you must temporarily lower the security level. A change might be required when either the IP addresses of the Control Center or HA partner change, or the key of the Control Center changes.
You can view and configure SCEP settings. When you expand the SCEP Control menu, you can select the following options from the Cmd list:
- Show Certificate Info – Displays information about the certificate retrieved by SCEP.
- Save Certificate to Clipboard – Exports the certificate to the clipboard (PEM).
- Save Certificate to File – Exports the certificate to a file (PEM).
- Initiate Pending Request – Starts the enrollment process immediately.
- Force SCEP Update – Starts an SCEP update.
- Set SCEP Debug ON – Turns SCEP debugging on. Additional debugging information is included in the SCEP log (Box > Control > SCEP).
- Set SCEP Debug OFF – Turns SCEP debugging off.
- Set SCEP Password – Prompts for the SCEP password. This option is available only if the SCEP password policy is set to Enter-Password-At-Box.
The Report window displays the results of operations selected in the above sections. For example, if a new network configuration is sent to the F-Series Firewall and has been verified, the Report window shows the results of the consistency check.