We use cookies on our website to ensure we provide you with the best experience on our website. By using our website, you agree to the use of cookies for analytics and personalized content.This website uses cookies. More Information
It seems like your browser didn't download the required fonts. Please revise your security settings and try again.
Barracuda CloudGen Firewall

NextGen Firewall F300 / F301 Revision A

  • Last updated on

F300-A-Front.png

Opening your Barracuda Networks appliance or removing its warranty label unless instructed to do so by Barracuda Networks support will void your warranty and hardware support.

Barracuda Networks Appliance Safety Instructions

Always use the power supply shipped with the appliance.

Default Port Configuration

LabelOS NotationSpeed/TypeManagement Port
PORT1port110/100 MBit RJ45X
PORT2port210/100 MBit RJ45 
PORT3port310/100 MBit RJ45 
PORT4port410/100 MBit RJ45 
-port510/100 MBit RJ45 
-port610/100 MBit RJ45 
-port710/100 MBit RJ45 
-port810/100 MBit RJ45 

On Revision A models, NIC ports 5 to 8 are located behind the access cover on the empty right side of the appliance's front panel.

Hardware Specifications

ComponentSpecifications
CPUVIA 1.5 GHz
Memory2 GB
HDD1 x 2.5", 160 GB *
Flash Disk128 MB
LCD Module2 x 20 characters
USB2x USB 2.0
Form Factor1U rack mount
Dimensions (W/D/H)43.0 x 33.0 x 4.5 cm
 16.9 x 13 x 1.8 in
Net Weight9.9 lbs / 4.5 kg
Power SupplySingle, internal
Power Supply Input Voltage100 - 240 V, AC
Power Supply Output Voltage12 V, DC
Power Supply Voltage47 Hz - 63 Hz
Power Supply Watts100 W
Storage Temperature-20 °C - +70 °C
Operation Temperature0 °C - 40 °C
Relative Humidity5% - 95%, non-condensing
CertificationsCE, FCC, ROHS
Wi-Fi (F301 only)802.11 b/g or better extended range Wi-Fi adapter

* Revision A units built after July 15, 2012, are equipped with 1 x 2.5" 80 GB SSD.

The hardware specifications list was valid at the time this manual was published. The listed components are subject to change at any time, as Barracuda Networks may change hardware components due to technological advancements. Therefore, the list may not reflect the current hardware configuration of the Barracuda Networks NextGen Firewall F-Series or NextGen Control Center appliance it was delivered with.

Status LED

Your appliance is equipped with a variety of LEDs. One of them is the Status LED. It is labeled either with a heart symbol or the term Status. It indicates the appliance’s operational state by changing colors between green, orange and red, and by changing between blinking and steady glowing. The table below shows the different meanings of the different glowing states. 

ColorGlowing StateMeaning: InstallationMeaning: Normal Operation or Active Recovery Technology (ART) Operation
OffOff

Appliance is powered off or installation has not initialized far enough for LED control when installation is started.

Appliance is powered off.
GreenBlinkingNormal installation.

Appliance is either booting, shutting down, or performing a system update.

GreenSteady

Installation was completed successfully. Appliance is halted for reboot or installation was not yet initialized far enough for LED control.

Barracuda NextGen Firewall is up and running.
RedBlinkingError during installation.

An error has occurred, preventing the Barracuda NextGen Firewall from entering the up state.
If no orange light available: appliance is in ART mode.

RedSteady-Appliance is halted and may be disconnected.
OrangeBlinking--
OrangeSteady-Appliance is in ART mode.

Not all appliances support orange and/or red LED colors. Depending on the appliance type, the status LED might be on by default, and it might take some time during boot and installation to start either blinking or changing the color. Furthermore, the status LED might blink at different frequencies.

Serial Console Port

In order to establish a console connection to the appliance using a serial cable (Revision A: DB9, Revision B: RJ45), you need to configure the serial port on the terminal using the following parameters:

ParameterValue
Baud19200
Bits8
Stop bit1
ParityNone
HandshakeNone

LCD Display

Navigating

This security appliance features a key pad with four keys and an LCD panel on the left side of the front panel. These may be used to obtain certain information and to perform certain commands directly on the appliance.

KeyCommand
Left

Navigates back or acts like an Escape key while working in the LCD menu.

Up

Navigates up or increases a value.

Down

Navigates down or decreases a value.

Right

Navigates forwards or acts like an Enter key for confirming a configuration step.

LCD Display Menu

You may use the LCD display and the keypad to access certain appliance features. Use the up and down keys to navigate through the items of the main menu.

The LCD menu features the following items from top to bottom:

MenuMeaning
Appliance type, OS version, and release numberThis is the default display.
IP address and subnet maskShows the configured IP address and subnet mask of the appliance.
Time and dateShows time and date currently configured on the appliance.
Uptime of Barracuda OSThe uptime in days, hours, and minutes.
Serial number of the applianceUnique identifier for the appliance.
Shutdown menuEnables you to shut down the appliance.
Reboot menuEnables you to reboot the appliance.
Menu to change the management IP addressConfigure the IP address for the management port.
Menu to boot into ART during the next reboot

Enables you to set a flag that will cause the appliance to boot into ART the next time it is rebooted.
Once set, this flag cannot be deleted through the menu. When rebooted, the appliance will not start Barracuda OS, but ART instead. You may connect to the appliance by using the serial console or by SSH. A Control Center-managed box running in ART mode cannot be managed through the CC, although it will build a connection to the CC signalling its presence.

Last updated on