It seems like your browser didn't download the required fonts. Please revise your security settings and try again.
Barracuda CloudGen Firewall

This Firmware Version Is End-Of-Support

Documentation for this product is no longer updated. Please see End-of-Support for CloudGen Firewall Firmware for further information on our EoS policy.

Linux Networking Commands

  • Last updated on

To help you find and solve networking problems, this article describes some Linux utilities and their commonly used options and parameters. Usage examples for the utilities are also provided. For more information on any of the following utilities, see their man pages.

ip

The ip  tool is a TCP/IP interface configuration and routing utility. Use it to configure and view routing, devices, policy routing, and tunnels. You can also use it to configure network interfaces. To display all the options for this command, enter ip at the CLI.

ip a

Displays the list of used network interfaces (physical and virtual) with their assigned MAC addresses.

[root@winix:/]# ip a
1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/24 brd 127.0.0.255 scope host lo:loop
2: tap0: <BROADCAST,MULTICAST,NOARP,UP> mtu 1500 qdisc noqueue
    link/ether fe:fd:00:00:00:00 brd ff:ff:ff:ff:ff:ff
    inet 127.0.1.1/24 brd 127.0.1.255 scope host tap0:fw
3: tap1: <BROADCAST,MULTICAST,NOARP,UP> mtu 1500 qdisc noqueue
    link/ether fe:fd:00:00:00:00 brd ff:ff:ff:ff:ff:ff
    inet 127.0.2.1/24 brd 127.0.2.255 scope host tap1:vpn
    inet 169.254.1.11/32 scope global tap1:aux1
4: tap2: <BROADCAST,MULTICAST,NOARP,UP> mtu 1500 qdisc noqueue
    link/ether fe:fd:00:00:00:00 brd ff:ff:ff:ff:ff:ff
    inet 127.0.3.1/24 brd 127.0.3.255 scope host tap2:vpnpers
    inet 169.254.1.11/32 scope global tap2:aux2
ip r g <network address>

Displays information about the device that is bound to the specified IP address.

[root@winix:/]# ip r g 10.0.6.31
local 10.0.6.31 dev lo  src 10.0.6.31
    cache <local>  mtu 16436 advmss 16396
ip a a <IP> dev <device name>

Adds an IP address to the specified device.

The IP address is removed again when the network or the Barracuda CloudGen Firewall is restarted. A device route is only added if a netmask has been given with the IP address.

[root@winix:/]# ip a a 10.0.4.236 dev eth2
ip a d <IP> dev <device name>

Deletes an IP address from the specified device.

[root@winix:/]# ip a d 10.0.4.236 dev eth2

If you use this command to remove a box IP address, the Control daemon will take action and reintroduce the deleted IP addresses.

tcpdump

To inspect packets, use the tcpdump  utility. It is a sniffer tool that captures packets off a network interface and interprets them. It prints out the headers of packets on a network interface that match the Boolean expression. It understands all basic Internet protocols. It can also be used to save entire packets for later inspection.

OPTIONS

Use the following options to specify which network interfaces you want to inspect: 

  • -i [interface] | any
    Specifies an interface name. To execute  tcpdump  on all available interfaces, use  any . To combine multiple devices, use  and/or .

  • host <ip address>
    Specifies a host IP address. To combine multiple hosts, use  and/or .
  • port <port  number>
    Specifies a queried port. To combine multiple ports, use  and/or .
[root@winix:/]# tcpdump -i eth0 -nnn -s0 host 10.0.10.10 and host 10.0.10.11 and port 801
[root@winix:/]# tcpdump -v -vv -n -nn -s0 -i any host 192.168.10.1 and 212.72.195.42 and port 443
[root@winix:/]# tcpdump -v -vv -n -nn -s0 -i any -w /tmp/dump.cap host 192.168.10.1 and 212.72.195.42 and port 443

fsck

If HDD/MEM tests are passing without errors, use the fsck utility with the following options to check and repair file systems:

fsck -A -y

These options solve most of the possible errors after a power outage because the utility checks all file systems and attempts to fix most detected file system corruption.

rpm

To check the kernel module architecture, use the rpm utility with the following options:

rpm -q --qf="%{arch}" kernel