Default Port Configuration
|1||p1||10/100/1000 MBit RJ45||High Availability|
|2||p2||10/100/1000 MBit RJ45|
|3||p3||10/100/1000 MBit RJ45|
|4||p4||10/100/1000 MBit RJ45||DHCP|
|5||p5||10/100/1000 MBit RJ45|
|6||p6||10/100/1000 MBit RJ45|
|7||p7||10/100/1000 MBit RJ45|
|8||p8||10/100/1000 MBit RJ45|
|9||p9||10/100/1000 MBit RJ45|
|10||p10||10/100/1000 MBit RJ45|
|11||p11||1 GbE Optical Fiber SFP|
|12||p12||1 GbE Optical Fiber SFP|
|13||p13||1 GbE Optical Fiber SFP|
|14||p14||1 GbE Optical Fiber SFP|
|15||p15||1 GbE Optical Fiber SFP|
|16||p16||1 GbE Optical Fiber SFP|
|17||p17||1 GbE Optical Fiber SFP|
|18||p18||1 GbE Optical Fiber SFP|
|19||p19||10 GbE Optical Fiber SFP+|
|20||p20||10 GbE Optical Fiber SFP+|
|Serial console||1 [RJ45]|
|Size [GB]||240 GB or higher|
|Size, Weight, Dimensions|
|Appliance weight [kg]||10|
|Carton weight with appliance [kg]||16|
|Appliance size: width x depth x height [mm]||440 x 480 x 44|
|Carton size: width x depth x height [mm]||650 x 640 x 200|
|Form factor||1U Rack Mount|
|Hardware crypto accelerator||-|
Single, internal (models F600 D.C10 and F600 D.F10),
|Noise emission [db/A]||N/A|
|Operating temperature [°C]||0 to +40|
|Storage temperature [°C]||-40 to +75|
|Relative humidity (non-condensing / non-operating)||10% to 85%|
|Certifications & Compliance|
|CE electrical safety||Yes|
|Power & Efficiency|
|Power supply type||Internal|
|Power type [AC/DC]||AC|
|Input rating [Volts]||100-240|
|Input frequency [Hz]||50-60|
|Wattage / max. power draw [W]|
|Max. power draw (@ 230V) [A]||2.6|
|Max. heat dissipation [W]||300|
|Max. heat dissipation [BTU]||1024|
|Energy efficiency [average]||> 80%|
LEDs and Acoustic Signals
Your appliance is equipped with a variety of LEDs. One of them is the Status LED. It is labeled either with a heart symbol or the term 'Status'. It indicates the appliance’s operational state by changing colors between green and red and by changing between blinking and steady glowing. The tables below show the different meanings of the different glowing states and acoustic signals:
|LED Color||Status||Meaning Installation||Meaning Operation|
All LEDs Off
Appliance is powered off or installation has not initialized far enough for LED control when installation is started.
|Appliance is powered off.|
Power LED front side - GREEN
Installation was completed successfully, appliance is halted for reboot or installation was not yet initialized far enough for LED control.
|Appliance is plugged in and is on.|
|Both Status LEDs front side - GREEN and RED||Off||Installation has not initialized far enough for LED control when installation is started.||-|
Status LED front side - GREEN
Installation was completed successfully, appliance is halted for reboot.
|Appliance is up and running.|
|Status LED front side - GREEN||Blinking||Normal installation.||Appliance is either booting, shutting down, or performing a system update.|
Status LED front side - RED
|Appliance is halted and may be disconnected.|
|Status LED front side - RED||Blinking||Error during installation.||An error has appeared preventing the appliance from entering the up state.|
|Both Status LEDs front side - GREEN and RED||Steady||-||Appliance is in ART mode.|
Disc LED front side - YELLOW
Appliance is reading or writing on storage.
Appliance is accessing the internal storage.
Port LEDs - GREEN/YELLOW
Data transfer – Yellow (10/100 Mbps)
|Port in use.|
|Right steady||-||Port is on.|
|PSU LEDs - GREEN||Steady||PSU modules connected and running||Power supply unit is up and running.|
|Off||Power defective, standby, or shutdown||Power supply unit is off or in standby mode.|
|Acoustic Signal||Frequency||Meaning Installation|
Unit starts booting
|Beep||3 times||Installation is completed successfully and appliance is halted for reboot. After reboot, one beep indicates booting.|
Serial Console Port
In order to establish a console connection to the appliance using a serial cable (Revision A: DB9, other revisions: RJ45), you need to configure the serial port on the terminal using the following parameters:
This CloudGen WAN appliance features a key pad with four keys and an LCD panel on the left side of the front panel. These may be used to obtain certain information and to perform certain commands directly on the appliance.
Navigates back or acts like an Escape key while working in the LCD menu.
Navigates up or increases a value.
Navigates down or decreases a value.
Navigates forth or acts like an Enter key for confirming a configuration step.
|Enter / Check||Enter key for confirming a configuration step|
LCD Display Menu
You may use the LCD display and the keypad to access certain appliance features. Use the up and down keys to navigate through the items of the main menu.
The LCD menu features the following items from top to bottom:
|Appliance type, OS version and release number||This is the default display.|
|IP address and subnet mask||Shows the configured IP address and subnet mask of the appliance.|
|Time and date||Shows time and date currently configured on the appliance.|
|Uptime of Barracuda OS||The uptime in days, hours, and minutes.|
|Serial number of the appliance||Unique identifier for the appliance.|
|Shutdown menu||Enables you to shut down the appliance.|
|Reboot menu||Enables you to reboot the appliance.|
|Menu to change the management IP address||Configure the IP address for the management port.|
|Menu to boot into ART during the next reboot|
Enables you to set a flag that will cause the appliance to boot into ART the next time it is rebooted.