We use cookies on our website to ensure we provide you with the best experience on our website. By using our website, you agree to the use of cookies for analytics and personalized content.This website uses cookies. More Information
It seems like your browser didn't download the required fonts. Please revise your security settings and try again.
Barracuda CloudGen Firewall

F800 Revision C

  • Last updated on
F800 Model CCC

F800c.CCC_FrontRack.png

F800c-CCC-Back.png

F800 Model CCF

F800c.CCF_FrontRack.png

F800c-CCF-Back.png

F800 Model CCE

F800c.CCE_FrontRack.png

F800c-CCE-Back.png

Power Supply Unit for all Upper Models

psu_F800_F900.png

Supported Barracuda Network Module Combinations

Standard Model Port Configuration

Port LabelOS NotationSpeed/TypeManagement Port
MGMTMGMT10/100/1000 MBit RJ45X
IPMIIPMI10/100/1000 MBit RJ45X

 Hardware Specifications

Opening your Barracuda Networks appliance or removing its warranty label unless instructed to do so by Barracuda Networks support will void your warranty and hardware support. Barracuda Networks Appliance Safety Instructions

Interface

Model CCC

24x 1 GbE RJ45 Ethernet

Model CCF
  • 16x 1 GbE RJ45 Ethernet
  • 8x   1 GbE SFP
Model CCE
  • 16x 1 GbE RJ45 Ethernet
  • 4x 10 GbE SFP+
USB 2.02
Serial console1 [RJ45]
Data Storage
RAM [GB]24
Mass Storage
TypeSSD
Size [GB]430 GB or higher
Size, Weight, Dimensions
Appliance weight [lbs]26
Appliance weight [kg]12
Carton weight with appliance [lbs]44
Carton weight with appliance [kg]20
Appliance size: width x depth x height [lbs]17.2 x 22.4 x 1.7
Appliance size: width x depth x height [mm]440 x 570 x 44
Carton size: width x depth x height [in]23 x 30.5 x 9
Carton size: width x depth x height [mm]585 x 775 x 229
Form factor1U Rack Mount

Hardware

DisplayYes
CoolingFan
Environmental
Noise emission [db/A]< 75
Operating temperature [°F]+32 to +104
Operating temperature [°C]0 to +40
Storage temperature [°F]-4 to +167
Storage temperature [°C]-20 to +75
Operating humidity (non-condensing)10% to 85%
Certifications & Compliance
CE emissionsYes
CE electrical safetyYes
FCC emissionsYes
MTBF [system]
MTBF [yrs.]> 4
Power & Efficiency
Power supplyDual hot swap
Power supply typeInternal
Power type [AC/DC]AC
Input rating [Volts]100-240
Input frequency [Hz]50-60
Auto senseYes
Wattage / max. power draw [W]500
Max. power draw (@ 120V) [A]8
Max. power draw (@ 230V) [A]4
Max. heat dissipation [W]~ 400
Max. heat dissipation [BTU]~ 1,366
Energy efficiency [average]> 88%
Packaging content
ApplianceYes
Serial cableYes
Straight network cableYes
Direct power to wall outletYes
USB flash drive for recovery & installation

Yes

Quick start guideYes
2x Barracuda L-shape rack mount bracketYes
Barracuda rail kitYes

The hardware specifications list was valid at the time this manual was published. The listed components are subject to change at any time, as Barracuda Networks may change hardware components due to technological advancements. Therefore, the list may not reflect the current hardware configuration of the Barracuda appliance it was delivered with.

LEDs and Acoustic Signals

Your appliance is equipped with a variety of LEDs. One of them is the Status LED. It is labeled either with a heart symbol or the term 'Status'. It indicates the appliance’s operational state by changing colors between green and red and by changing between blinking and steady glowing. The tables below show the different meanings of the different glowing states and acoustic signals:

LED ColorStatusMeaning InstallationMeaning Operation

All LED Off

Off

Appliance is powered off or installation has not initialized far enough for LED control when installation is started.

Appliance is powered off.

Power LED front side - GREEN

Steady

Installation was completed successfully, appliance is halted for reboot or installation was not yet initialized far enough for LED control.

Appliance is plugged in and is on.
Status LED front side - GREEN/REDOffInstallation has not initialized far enough for LED control when installation is started.-

Status LED front side - GREEN

Steady

Installation was completed successfully, appliance is halted for reboot.

Appliance is up and running.
Status LED front side - GREENBlinkingNormal installation.Appliance is either booting, shutting down, or performing a system update.

Status LED front side - RED

Steady

-

Appliance is halted and may be disconnected.
Status LED front side - REDBlinkingError during installation.An error has appeared preventing the appliance from entering the up state.
Status LED front side - RED/GREENSteady-Appliance is in ART mode.

Disc LED front side - YELLOW

Blinking

Appliance is reading or writing on storage.

Appliance is accessing the internal storage.

Port LEDs - GREEN/YELLOW

Left blinking

Data transfer – Yellow (10/100 Mbps)

Port in use.
Right steady-Port is on.
Acoustic SignalFrequencyMeaning Installation
Beep1 time

Unit starts booting

Beep3 timesInstallation is completed successfully and appliance is halted for reboot. After reboot, one beep indicates booting.

Not all appliances support yellow and/or red LED colors. Depending on the appliance type, the status LED might be on by default and it might take some time during boot and installation to start either blinking or changing the color. Furthermore, the status LED might blink at different frequencies.

Serial Console Port

In order to establish a console connection to the appliance using a serial cable (Revision A: DB9, Revision B: RJ45), you need to configure the serial port on the terminal using the following parameters:

ParameterValue
Baud19200
Bits8
Stop bit1
ParityNone
HandshakeNone

LC Display

Navigating

This security appliance features a key pad with four keys and an LCD panel on the left side of the front panel. These may be used to obtain certain information and to perform certain commands directly on the appliance.

Keyboard ButtonCommand
Left arrow

Navigates back or acts like an Escape key while working in the LCD menu.

Up arrow

Navigates up or increases a value.

Down arrow

Navigates down or decreases a value.

Right arrow

Navigates forth or acts like an Enter key for confirming a configuration step.

LCD Display Menu

You may use the LCD display and the keypad to access certain appliance features. Use the up and down keys to navigate through the items of the main menu.

The LCD menu features the following items from top to bottom:

LCD MenuMeaning
Appliance type, OS version and release numberThis is the default display.
IP address and subnet maskShows the configured IP address and subnet mask of the appliance.
Time and dateShows time and date currently configured on the appliance.
Uptime of Barracuda OSThe uptime in days, hours and minutes.
Serial number of the applianceUnique identifier for the appliance.
Shutdown menuEnables you to shut down the appliance.
Reboot menuEnables you to reboot the appliance.
Menu to change the management IP addressConfigure the IP address for the management port.
Menu to boot into ART during the next reboot

Enables you to set a flag that will cause the appliance to boot into ART the next time it is rebooted.
Once set, this flag can not be deleted through the menu. When rebooted, the appliance will not start Barracuda OS, but ART instead. You may connect to the appliance by using the serial console or by SSH. A Control Center managed box running in ART mode cannot be managed through the CC, although it will build a connection to the CC signalling its presence.

Rack Mounting

For information on how to mount your appliance, see Rack Installation for Barracuda CloudGen Firewall F800 Revision C and F900 Revision A,B.

Last updated on