We use cookies on our website to ensure we provide you with the best experience on our website. By using our website, you agree to the use of cookies for analytics and personalized content.This website uses cookies. More Information
It seems like your browser didn't download the required fonts. Please revise your security settings and try again.
Barracuda CloudGen Firewall

NextGen Firewall F900 Revision A

  • Last updated on
Barracuda NextGen Firewall F-Series F900 model CCC (24x1 GbE copper network ports)

F900-CCC.png

F900.back.png

Barracuda NextGen Firewall F-Series F900 model CCE (16x1 GbE copper + 4x1 GbE SFP (fibre) network ports)

F900-CCE.png

Barracuda NextGen Firewall F-Series F900 model CFE (8x1 GbE + 8x1 GbE SFP (fibre) + 4x10 GbE SFP+ (fibre) network ports)

F900-CFE.png

Supported Barracuda Network Module Combinations

Opening your Barracuda Networks appliance or removing its warranty label unless instructed to do so by Barracuda Networks support will void your warranty and hardware support.

Barracuda Networks Appliance Safety Instructions

Always use the power supply shipped with the appliance.

Default Port Configuration

LabelOS NotationSpeed/TypeManagement Port
MGMTMGMT10/100/1000 MBit RJ45X

Hardware Specifications

Interface

Model CCC

  • 24x 1 GbE Copper
Model CCE
  • 16x 1 GbE Copper
  • 4x 10 GbE SFP+
Model CFE
  • 8x   1 GbE Copper
  • 8x   1 GbE SFP
  • 4x 10 GbE SFP+
USB 2.02
Serial / console1 [RJ45]
Memory
RAM [GB]24
Mass Storage
TypeSolid State
Size [GB]
  • 80 (system)
  • 300 (log, cache)
Size, Weight, Dimensions
Net weight [kg]18
Weight carton with appliance [kg]22
Appliance size: width x depth x height [mm]442 x 660 x 88
Carton size: width x depth x height [mm]590 x 870 x 290
Form factor2U Rack Mount

Hardware

DisplayYes
Hardware crypto acceleratorYes
CoolingFans
Power supply

Dual hot swap, internal

Environmental
Noise emission [db/A]N/A
Operating temperature [°C]0 to +40
Storage temperature [°C]-20 to +60
Operating humidity (non-condensing)5% to 95%
Certifications & Compliance
CE emissionsYes
CE electrical safetyYes
FCC emissionsYes
ROHS compliantYes
Power & Efficiency
Power supply typeInternal
Power type [AC/DC]AC
Input rating [Volts]100-240
Input frequency [Hz]50-60
Auto senseYes
Wattage / max. power draw [W]500
Max. power draw (@ 230V) [A]2,6
Max. heat dissipation [W]300
Max. heat dissipation [BTU]1024
Energy efficiency [average]> 80%

The hardware specifications list was valid at the time this manual was published. The listed components are subject to change at any time, as Barracuda Networks may change hardware components due to technological advancements. Therefore, the list may not reflect the current hardware configuration of the Barracuda Networks NextGen Firewall F-Series or NextGen Control Center appliance it was delivered with.

Status LEDs and Acoustic Signals

Your appliance is equipped with a variety of LEDs. One of them is the Status LED. It is labeled either with a heart symbol or the term Status. It indicates the appliance’s operational state by changing colors between green, orange, and red, and by changing between blinking and steady glowing. The table below shows the different meanings of the different glowing states. 

ColorGlowing StateMeaning: Installation

Meaning: Normal Operation or Active Recovery Technology (ART) Operation

OffOff

Appliance is powered off or installation has not initialized far enough for LED control when installation is started.

Appliance is powered off.
GreenBlinkingNormal installation.

Appliance is either booting, shutting down, or performing a system update.

GreenSteady

Installation was completed successfully. Appliance is halted for reboot, or installation was not yet initialized far enough for LED control.

Appliance is up and running.
RedBlinkingError during installation.

An error has occurred, preventing the appliance from entering the up state.
If no orange light available: appliance is in ART mode.

RedSteady-Appliance is halted and may be disconnected.
OrangeBlinking--
OrangeSteady-Appliance is in ART mode.
Acoustic SignalFrequencyMeaning Installation
Beep1 time

Unit starts booting

Beep3 timesInstallation is completed successfully, and appliance is halted for reboot. After reboot, one beep indicates booting.

Not all appliances support orange and/or red LED colors. Depending on the appliance type, the status LED might be on by default, and it might take some time during boot and installation to start either blinking or changing the color. Furthermore, the status LED might blink at different frequencies.

Serial Console Port

In order to establish a console connection to the appliance using a serial cable (Revision A: DB9, Revision B: RJ45), you need to configure the serial port on the terminal using the following parameters:

ParameterValue
Baud19200
Bits8
Stop bit1
ParityNone
HandshakeNone

LCD Display

Navigating

This security appliance features a key pad with four keys and an LCD panel on the left side of the front panel. These may be used to obtain certain information and to perform certain commands directly on the appliance.

KeyCommand
Left

Navigates back or acts like an Escape key while working in the LCD menu.

Up

Navigates up or increases a value.

Down

Navigates down or decreases a value.

Right

Navigates forwards or acts like an Enter key for confirming a configuration step.

LCD Display Menu

You may use the LCD display and the keypad to access certain appliance features. Use the up and down keys to navigate through the items of the main menu.

The LCD menu features the following items from top to bottom:

MenuMeaning
Appliance type, OS version, and release numberThis is the default display.
IP address and subnet maskShows the configured IP address and subnet mask of the appliance.
Time and dateShows time and date currently configured on the appliance.
Uptime of Barracuda OSThe uptime in days, hours, and minutes.
Serial number of the applianceUnique identifier for the appliance.
Shutdown menuEnables you to shut down the appliance.
Reboot menuEnables you to reboot the appliance.
Menu to change the management IP addressConfigure the IP address for the management port.
Menu to boot into ART during the next reboot

Enables you to set a flag that will cause the appliance to boot into ART the next time it is rebooted.
Once set, this flag cannot be deleted through the menu. When rebooted, the appliance will not start Barracuda OS, but ART instead. You may connect to the appliance by using the serial console or by SSH. A managed F-Series Firewall running in ART mode cannot be managed through the Control Center, although it will connect to the Control Center to signal its presence.

Rack Mounting

For information on how to mount your appliance, see Rack Installation for Barracuda NextGen Firewall F-Series F800 and F900.

Last updated on